VERTEX Electronic Flash VT520

VERTEX Electronic Flash VT520 แฟลชนอกราคาประหยัด กำลังแฟลช Guide Number 33 หัวแฟลชสามารถปรับก้มเงย หมุุนซ้ายขวาได้ หัวแฟลชมีแผ่นสะท้อนแสง และ มีตาแมวในตัว สามารถใช้ร่วมกับ Battery Pack ได้เพื่อเพิ่มเวลาในการใช้งานให้นานยิ่งขึ้น รับประกันตัวแฟลช 1 ปี

Control Panel :
- ON/OFF Button -------Turn the flash On or Off
- MODE Button ---------Switch Between M/S1/S2 mode
- Test Button ------------ Fire a test flash
- Power Up Button (+) --- Increase the power output of the flash
- Power Down Button ( - ) --- Decrease the power output of the flash

1. Battery installation :
- Open the battery cover
   Slide the battery cover along the arrow direction and then open it by thumb.
- Insert Batteries
   Install the batteries according to the direction indicated by the sicker in the battery holder and make sure the + and – battery contact are correctly inserted at the battery compartment .
- Slide the battery cover along the arrow direction and slide it back in place . The battery cover will be locked when there is a “Click” sound.

Attention : The battery contact pin isn’t regular; therefore, it may lead to poor contact when using other type of AA batteries except AA Alkaline battery.

Take care of the hot battery when changing them after continuous flashes.
(1) Switch to the ON, the flash will start charging (the charging indicator is dim). After several seconds, the charging indicator turns red and TT520 is ready to shoot.
(2) For a test flash, press the test button. After use, press the ON/OFF to OFF to power off.
(3) If the red charging indicator lamp flickers in every 1s, it indicates low battery. In such case, the power will turn off automatically and you need to replace the batteries.

2. Power Control
(1) The flash unit has 8 steps of power output control which indicated by 8 pieces of LED lamp for different level.
(2) Press "+" to make power higher and they are 1/128,1/64,1/32,1/16,1/8,1/4,1/2,1/1.Otherwise, press "-" to make power lower.

Three flash Mode M/S1/S2 for your applicable to different effect.

3. M Mode
Press the MODE key to M Mode. In this mode, you can set TT520 on to your camera hot shoe or speedlite trigger hot shoe to trigger the flash unit. When shooting, adjust the flash power and press the camera shutter, the flash light will flash under the camera synchronous signal.

4. S1 Mode
(1) Press the MODE key to S1 Mode. The Mode is applicable for slave flash in order to create many lighting effects. It is respectively applicable for manual flash environment.
(2) When the flash is S1 mode, it will fire synchronously when the master flash fires, comparable with the effect by the use of radio trigger.

5. S2 Mode
(1) Press the MODE key to S2 Mode. The mode is applicable for slave flash in order to create many lighting effects. It is respectively applicable for TTL flash environment. The flash unit won't flash synchronously with the first flash but the second flash from the master flash.

6. Power-Saving Function
(1) To save battery power, the flash will enter stand-by state in about 30 minutes of idle use. Press any button to wake it up.
(2) In S1/S2 mode, the flash will enter stand-by state in about 60 minutes of idle use. Press any button to wake it up.
(3) In Power-saving mode, the charging indicator flickers in every 3 seconds. Other indicators are turned off.

7. Protection Function
(1) Protection in continuous flashes
To prevent the flash head from getting too hot and damage, please do not flash over 20 times when in power lever 1/2, 1/1. Please cool down the flash unit for at least 10 minutes. The over-temperature protection function will be activated if you continue to flash after 20 times. In this state the charging time will turn to 10-25s. Please cool down the flash unit around 10 minutes and it will turn to normal state.
(2) Systematic over-temperature protection
When the inner circuit is over-heating, which indicates over use of the flash unit, the inner circuit will shut down power automatically. The flash unit will turn to normal state after the inner circuit is cooled down. Specification : Guide Number: GN33 (ISO 100) Flash Mode: M, S1, S2 Vertical Rotation Angle: 0~90° Horizontal Rotation Angle: 0~270° Power: 4xAA batteries (Alkaline or Ni-MH) Flash Times: 100-1500 times (AA alkaline batteries used) Recycle Time: approx 0.5-5s (AA alkaline batteries used) Light Quantity Output Control: with 1/8 - stop increment Color Temperature: 5600K+200K Flash Duration: 1/1800s~1/2000s

Specification :
Guide Number : GN33 ( ISO 100 )
Flash Mode : M, S1, S2
Vertical Rotation Angle : 0~90°
Horizontal Rotation Angle : 0~270°
Power : 4 x AA Batteries ( Alkaline or Ni-MH )
Flash Times : 100-1500 Times ( AA alkaline batteries used )
Recycle Time : Approx 0.5-5s ( AA alkaline batteries used )
Light Quantity Output Control : With 1/8 - Stop increment
Color Temperature : 5600K+200K
Flash Duration : 1/1800s~1/2000s

สินค้าที่คุณอาจจะสนใจ

Nissin Flash Speedlite Di622 Mark II ฿ 7,890.00 ฿ 6,390.00 ท่านประหยัดได้: ฿ 1,500.00

Yongnuo YN560 + Eneloop AA*4 + แท่นชาร์จ ฿ 2,600.00 ฿ 2,600.00 ท่านประหยัดได้: 0.00%

Yongnuo YN-565EX ETTL Flash + Eneloop AA*4 + แท่นชาร์จ ฿ 5,490.00 ฿ 4,990.00 ท่านประหยัดได้: ฿ 500.00

VERTEX Digital Slave Flash ฿ 800.00 ฿ 650.00 ท่านประหยัดได้: ฿ 150.00